RLH Industries 16 Channel T1 Over Ethernet Multiplexer System Dokumentacja Strona 1

iMux Fiber OpticMultiplexer SystemQuick Start GuideQS-001 2014A-0911RLH Industries, Inc.

Rear PanelAny of the modules may be plugged into any position, called a Tributary Slot. These are referred to as TB1~TB4.Refer to the Specifications s

4 Channel RS-232 Module4xRS-232 module, HD68 to 4 DB-9 connectors to RS-232 interface. Breakout adapter cable is included.10(f) RS232 tributary card A

4 Channel Analog Phone (POTS) ModulesAnalog phone uses RJ-11 connectors and are supplied as FXS/Sub side and FXO/CO side modules.The FXO/CO module is

4 Channel 2/4 Wire Analog Data/Audio/SCADA ModuleFour Analog 2/4 Wire Data/Audio/SCADA modules use RJ-11 connectors.Each channel has 300Hz ~ 3.4kHz ba

Setting E&M Jumpers and SwitchesUse the J2 jumper and the J4 DIP switches to set the E&M module mode to Master or Slave depending on the place

detectOff-hookOff-hookOn-hookOn-hookEMGNDTRT14-WireAudio4-WireAudioTrunk CircuitSignalling Unit4 Wire E&M Card - MasterR1E7682354MT(-48V)Fiber Opt

AcronymsCommonly used acronyms and abbreviationsAcronym/AbbreviationDescriptionB8ZSBipolar 8 Zero SubstitutionFXO/COCentral Office Side EquipmentFXS/Su

3." Before InstallingObserve Special Handling RequirementsBe careful when handling electronic componentsATTENTIONELECTROSTATICSENSITIVEDEVICES• T

Prepare for InstallationCheck for shipping damageCarefully unpack and inspect the unit and accessories. Contact RLH immediately if any components are

Typ i ca l a pp l ic at i on en vi ro nm e nt sInstall the fiber optic cable prior to installing the iMux system.Required power sourcesYou will nee

RLH Industries, Inc.Copyright © 2013 RLH Industries, Inc. All rights reserved.No part of this document may be copied or distributed without permissio

4." Quick StartEasy InstallationBefore starting•Review the safety information in section 1. Important Information•Familiarize yourself with the i

Connect ethernet cables• Attach ethernet cables to the RJ-45 ethernet ports labeled LAN1 through LAN4 on the front panel of the iMux.Connect data/phon

5." SpecificationsGeneral SpecificationsAlarmContact Capacity4 relay contacts (DB-9 connector)AlarmExternal AlarmDB-9 connectorPower SupplyAC115/2

Service Module SpecificationsT1 Interface ModuleChannel Capacity4 x T1T1 Interface ModuleBit Rate1.544 MbsT1 Interface ModuleLine CodeB8ZS per ANSI T1

6." Ordering InformationBase SystemsPart NumberDescriptionPower 1Power 2Dimensions (1RU) RLH-IMUX-V-2iMUX BASE SYSTEM DUAL 48 VDC INPUT PWR48VDC4

Optical ModulesPart NumberDescriptionSideDistanceFiberPart NumberMultimode STiMux Optical Module-2 km/1.2 mi62.5 μmRLH-OM-04-1Bi-DirectionalSingle-mo

7." SupportTec hn ic al S up po rtEmail:support@fiberopticlink.com24/7 technical support:Toll Free 1-855-RLH-24X7Toll Free 1-855-754-2497Contact

Contents1." Important InformationIntended Audience! 5Conventions! 5General Safety Practices! 52." IntroductionProduct Description! 6Standard

Prepare for Installation! 18Check for shipping damage# 18Verify system contents # 18Verify matching optical module and fiber modes# 18Site Requirements

1." Important InformationIntended AudienceThis manual is intended for use by knowledgeable telco/network installation, operation and repair perso

2." IntroductionProduct DescriptionThe iMux is a powerful fiber optic modular multiplexer capable of providing up to 16 channels of T1, RS232, 2/

Application DiagramsT1T12/4 WireDataRS-232 RS-232Ethernet(VLAN/QoS)Ethernet(VLAN/QoS)2/4 WireDataPOTS(FXS)POTS(FXO)RLH iMux RLH iMuxLAN1 LAN2 LAN3 LAN

Front PanelRSTMAJMINLBKRDIPWRLCKACOLOS/LOF/AIS123 41234E1/V35EXT CLK CRAFT SL-2100TX RXWKLOSLSRONTX RXWKLOSLSRONLAN1 LAN2 LAN3 LAN4 MGMTFront Panel LE

Module Status LEDsRSTMAJMINLBKRDIPWRLCKACOACOLOS/LOF/AIS1 2 3 41234E1/V35PORTSCRAFT TX RXWKLOSLSRTX RXWKLOSLSRLAN1 LAN2 LAN3 LAN4 MGMTIMux slot num